![]() ![]() So let's say the computer's IP address is 192.168.177.12. In our test, the default IP address of the camera we use is 192.168.177.100, and now you need to change your computer's IP address to, where x identifies the node/host and is the number between 2 and 254. So in Step 3, you get your security camera's default IP address. Change the computer's IP address to the same network prefix of the IP camera. Launch it and it will automatically scan all the cameras in the same local LAN and show the default IP address (every camera has a default and unique IP address when it leaves the factory). There should be surveillance software from the same supplier with the camera. What you need to do now is to scan and find out the camera's IP address. But you still can't view the camera on the computer. Now the security camera is connecting to your computer basically and physically. Scan and find out the security camera's IP address on the computer. If your computer has a network already, disable it - make sure your computer is offline. Then connect the other end of the network cable to the computer. Find the network connector from that cable and use the network cable to connect to it. Normally there would be a 2-in-1 or 3-in-1 cable attached from the camera. Use the network cable to connect to the camera and the computer. For a PoE camera, ask the supplier and buy one that's workable for the camera. Normally, when you buy a WiFi IP camera, it comes with a power adapter. Use the power adapter to get the camera plugged-in and charged. You need to prepare the camera's power adapter and a network cable. Here's how to connect your security IP camera directly to a PC/Mac without an NVR or DVR, without a router network, without WiFi, and without any costs or complicated configurations. Important Note: The methods recommended below may NOT apply for the battery-powered security cameras, which require initial setup on your phones.Ĭonnect a WiFi or PoE Camera Directly to PC/Mac (without Internet) PoE (Wired) Camera without Injector/Switch Connect Directly to PC/Mac (without Internet) To make it easier for you to find the right solution, you can click and jump directly to the section you want.įor example, if your camera is a PoE camera, then you can choose option 3 or 4. In this case, please tap input UID/IP under the scan window, choose IP, enter the IP address of the camera/NVR and tap Next to proceed.5 Methods to Connect Your Security IP Camera to PC/Mac: ![]() Knowing the IP address of the camera or NVR, we can also add it by manually entering the IP address. Add by entering IP address of the Reolink device In this case, please tap input UID/IP under the scan window, choose UID, enter the UID of the camera/NVR and tap Next to proceed. If the QR code sticker on the device is lost or blurry, you can still add it by manually entering the UID numbers. (For NVR Kit, we only need to scan the QR code on the NVR box to add the whole system to the App.) Please launch the Reolink App, tap the " +" button in the top-right corner, and scan the QR code on the camera or NVR. If the Reolink device is not added automatically nor can it be found in LAN, we may add it by scanning the QR code. Add by scanning the QR code of the Reolink device Tap the "+" option in the top-right corner of the home page, then choose LAN to proceed. When the add devices automatically option is disabled, you can still add a Reolink camera or NVR in the same network by searching in LAN. If yes, you may need to enter the login password if the device has been set up. Please check the device list on the Reolink App to see if your camera or NVR is added. With this function, Reolink cameras or NVRs that are connected to the same local network as your phone is will be detected and added to the App automatically. Add by using add devices automaticallyīy default, the Reolink App has the add devices automatically option enabled. To add Reolink cameras or NVRs to Reolink App, please refer to the instructions below.įor cameras or NVRs that are not set up yet, please finish the initial setup first.įor cameras or NVRs that have been set up, there are 3 methods to add them to Reolink App. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |